Conduit Fittings - Page 2 - Super Savings! Save up to 35%
Super Savings! Up to 35% off on Conduit Fittings at Peri Matrix, Page 2. Top brands include Steel City, Sioux Chief, Cantex, Carlon, Linear Solutions, Garvin Industries, Thomas & Betts, Taco Metals, Morris Products, uxcell, Tuff-Seal, Ideal, & STI. Hurry! Limited time offers. Offers valid only while supplies last.
Thomas & Betts 2559 Liquidtight Strain Relief Cord Connector 1-1/4" Male, Die-Cast Zinc (5 Pack)
mpn: 2559, ean: 0642337966750,
4.7 out of 5 stars with 48 reviews
Thomas & Betts Straight Cord connector has die-cast zinc construction with neoprene bushing that provides high impact resistance and ductility. It measures 2-3/32 Inch diameter x 2-5/32 Inch. Connector has a throat diameter of 1-17/64 Inch and thread size of 5/8 Inch length. It is designed to connect a conductor size of 1.065 - 1.205 Inch. It can withstand a temperature of 105 deg C. Connector features gland nut design that restricts the cable bending. It forms a liquid tight connection and
Service Entrance Cap, 1Piece, 2 1/2 In, PVC
4.5 out of 5 stars with 33 reviews
Easy to install, this fitting is rust and corrosion resistant. It is designed to install atop vertical conduits, usually outdoors, to receive open wires from an electrical service line. Can help in preventing rainwater from entering the conduit. Service Entrance Cap, Conduit Fitting Type Cap, Conduit Trade Size 2-1/2 In., Conduit Fitting Material PVC, Overall Length 15 In., For Use With Schedule 40 or 80 PVC Conduit, Standards ULUSA.
3-1/2 Inch Plastic Insulating Bushing-5 per case
You Save: 14%
mpn: IB-350, ean: 0785592405258,
4.0 out of 5 stars with 23 reviews
3-1/2 Inch plastic insulating bushings are used to protect low voltage cables from damage caused by sharp edges on the end of EMT conduits. They may be used with many low voltage cables including, coaxial, computer, telephone, category 5E, category 6, audio, video, fire alarm system, security system, and thermostat cables. Garvin Industries’ plastic insulating bushings have a tight press fit that firmly holds it while the installer snaps it in place on the end of conduits; they will not fall
Thomas & Betts E986L 3" TYPE LB CONDUIT BODY (Pack of 4)
sku: 3167525, mpn: E986L, ean: 0034481065494,
4.2 out of 5 stars with 33 reviews
3'' Rigid non-metallic Type LB conduit body.Material: Non-Metallic. Textured lids. Foam-in-place gasket. For use with rigid/IMC conduit. Size: 3 IN.
2-1/8 Inch Deep Three Gang Multi Device Switch Box
You Save: 18%
mpn: MGSB-3, ean: 0646635935951,
4.4 out of 5 stars with 32 reviews
2-1/8 Inch deep, three gang multi device switch boxes allow electricians to install multiple devices in one box location. A larger wire capacity box can be used for extra deep devices. Garvin Industries’ labor saving multiple device ears permit various electrical devices to be installed in one conduit box. The drawn boxes are ideal for exposed locations.2-1/8 Inch Deep, Three Gang Multi Device Switch Box-2 Pack.
Taco Outrigger Sock Cord Glass
You Save: 12%
mpn: COK-0021-2, ean: 0630838085094,
4.9 out of 5 stars with 10 reviews
Taco marine shock cord with glass eye popular taco marine sport fishing rigging kit accessory size: 12 inch cord color: black qty.: 2-packGreat for any outdoor enthusiast. Made in the United States. Very easy to Use.
Push in Conduit Hanger with Hammer on Beam Clamp Side Mount
You Save: 35%
mpn: CHO-5025-SM, ean: 0646635935524,
4.2 out of 5 stars with 33 reviews
These push in conduit hanger/beam clamp assemblies are used to support rigid, emt and flexible metal conduits that must be mounted along the side of structural beam edges. Beam clamp quickly and easily hammers on beam edge allowing sharp teeth to bite on the beam and prevent vibratory loosening. push in conduit hanger rotates 360 degrees to accommodate multi-directional conduit runs.Push in Conduit Hanger with Hammer on Beam Clamp, Side Mount, for 1/2 Inch EMT and 1/8-1/4 Inch Flange-10 Pack.
Morris Products 21734 Plastic Insulating Bushing, 1" Size (Pack of 50)
mpn: 21734, ean: 0601986217347,
4.8 out of 5 stars with 15 reviews
1/2” wide. Threaded plastic inserts are UL/CSA Listed. Dimension Measurements = Inches. UL/CSA Listed.Electrical Bushings Plastic Insulating Bushings - Flame retardant Threaded Plastic Inserts for conduit.. Use to Protect Conductors in Rigid or IMC Conduit from Abrasion/Damage during Pull. Thermoplastic material-heat, impact and torque resistance. Strong reinforcing ribs & rim around bottom. Flame retardant Polypropylene (Rated to 221°F, 105°C).
uxcell Black PG13.5 Water Resistance Cable Gland Fixing Connector Joints Fastener 100 PCS
You Save: 3%
4.0 out of 5 stars with 16 reviews
There are PG13.5 model cable glands, Used for fixing cables, water resistance design.Special design of the clamping die and rubber part, wide clamping range, strong stretching resistance, no damage to cables and devices.Without disassembly, cable can be inserted through directly then tightened easily.Applicable to machinery control boxes, distribution panels, electrical appliances, machines, etc.Country of Manufacture: CHINA; Material: Plastic. Net Weight:881g; Package Content: 100(+/-2%) x
Malleable Iron Liquid Tight Conduit Fittings - Insulated Throat (45-Degree, 3/4 In. (10-Pack))
4.5 out of 5 stars with 9 reviews
Compatible for use with metallic type B liquid tight conduit to suit multiple applications. Linear Solutions liquid-tight connectors seal out water, oil & dust and any particles that could damage circuitry. Insulated throat for adds protection for wires and aids in wire pulling. Fabricated with the highest quality malleable iron and galvanized (zinc electroplated) for added durability and rust prevention. Includes a steel locknut. Approved for use in wet locations. UL (USA) and CUL (Canada)
1 Inch Threaded Hub-10 per case
mpn: H100, ean: 0785592405029,
4.5 out of 5 stars with 40 reviews
1 Inch threaded hubs are used with ground pipe clamps to connect rigid conduits to water pipes for grounding.1 Inch Threaded Hub.
Conduit Bender Head, 3/4 EMT, 1/2 Rigid
mpn: 74-002, ean: 0696498595427,
4.9 out of 5 stars with 40 reviews
Conduit Bender Head, Handle Not Included, EMT Size 3/4 In., Rigid/IMC Size 1/2 In., Centerline Bend Radius 5-13/64 In., Ductile Iron Construction, Benfield Markings, Yes Pedal, For Conduit BendingUSA.
Thomas & Betts 5332 Liquidtight Connector (Pack of 25)
You Save: 11%
mpn: 5332, ean: 0786210053325,
4.8 out of 5 stars with 51 reviews
The T&B 5332 is a Liquid tight connector. Used to positively bond conduit to a box or an enclosure, this connector is best used where flexible metal raceway is installed in outdoor or indoor locations where exposed to continuous or intermittent moisture. This connector installs quickly and easily with low torque effort. From the earliest days of electrification over 100 years ago, Thomas & Betts has been a leader in providing products for commercial and industrial construction, industrial plant
3 Inch Offset Conduit Nipple-1 per case
You Save: 1%
mpn: OCN300, ean: 0785592991874,
4.3 out of 5 stars with 35 reviews
3 Inch offset nipples are used to connect two boxes or enclosures when knockouts are not in line, they offset the conduits by 3/4 Inch. Garvin Industries’ offset nipples have a rugged metallic construction to ensure mechanical protection and durability. They also reduce the need to do offset conduit bending.3 Inch Offset Conduit Nipple.